Acom LS-100 Dokumentacja

Accessory Decoder LS 100/110 1DIGITAL plusAccessory decoders are the link between your NMRA DCCsystem and your function devices (that is turnouts, sig

10 Accessory Decoder LS 100/110Illustration 4: Connecting devices to the LS100/LS110 functionoutputs

Accessory Decoder LS 100/110 11DIGITAL plusConnecting a motorized turnout driveTo connect motorized turnout drives, you need adapter LA010(Illustratio

12 Accessory Decoder LS 100/110For information on how to read the turnout position on hand heldcontroller LH100 or another device, please refer to the

Accessory Decoder LS 100/110 13DIGITAL plusIt is required that the output to be optionally controlled by anexternal push button not be set to flashing

14 Accessory Decoder LS 100/110The shared address area of LS100/LS110/LS120 and LR100Information about the positions of turnouts and signals fromacces

Accessory Decoder LS 100/110 15DIGITAL plusPress the programming button on the LS100/LS110 and keep itpressed until the LED lights up and stays lit (t

16 Accessory Decoder LS 100/110Programming address and settings through theprogramming output of LZ100Address and other settings of LS100/LS110 are st

Accessory Decoder LS 100/110 17DIGITAL plusThe pulse duration is determined by the following values:valuepulse duration(seconds)valuepulse duration(se

18 Accessory Decoder LS 100/110Illustration 7: Connecting LS100/LS110 to theprogramming output of LZ100To program address and settings you need your c

Accessory Decoder LS 100/110 19DIGITAL plusNext LH100 will show you the most recently chosenprogramming mode. Press the ‘+’ key repeatedly until thedi

2 Accessory Decoder LS 100/110Whats new in the upgraded LS100/110?A push button and an LED have been added to theLS100/110 to make programming easier.

20 Accessory Decoder LS 100/110“ERR 02”. Ignore this message, since LS100/LS110 is not ableto confirm successful programming to the command station.Ne

Accessory Decoder LS 100/110 21DIGITAL plusTable 5 Feedback addresses / turnout addresses:F-Feedback address; T-Turnout address, FE-Feedback informati

22 Accessory Decoder LS 100/110Trouble shootingProblem Cause SolutionTurnout does not throw, theLED does not flicker while aWrong turnout addressenter

Accessory Decoder LS 100/110 23DIGITAL plusLenz GmbH does everything it can do to ensure that its productsare free from defects and will operate for t

24 Accessory Decoder LS 100/110Please contact your dealer or authorized Lenz GmbH warrantycenter for specific instructions and current service charges

Accessory Decoder LS 100/110 3DIGITAL plusSpecifications of LS100/LS110Up to 4 function devices each with a twin output can beconnected to each LS100/

4 Accessory Decoder LS 100/110pulse duration a new switching command is received by theLS100/110, the output remains active for another pulseduration.

Accessory Decoder LS 100/110 5DIGITAL plusInstalling the accessory decoder LS100/LS110Connecting the LS100/LS110 to a power station and/orseparate pow

6 Accessory Decoder LS 100/110DCC system and does not use a separate power supply line topower the LS100/110. The second option uses an externalpower

Accessory Decoder LS 100/110 7DIGITAL plusIllustration 3: Connecting the feedback bus on LS100

8 Accessory Decoder LS 100/110connected to the corresponding terminals on a power stationLV100/LV101. Terminals ‘≈≈‘ are connected to a transformer wi

Accessory Decoder LS 100/110 9DIGITAL plusIn the following table the common wire colors from some trackmanufacturers, is matched to the wire numbers i